Protection board wiring video:Https://v.qq.com/x/page/e05497w1x6t.html
Note : Check the version you need carefully before you place order ~ :)
300A/200A/150A/100A/70A MOS Screen : 300A/200A/150A/100A/70A Current + MOS Tube + Display Screen
300A/200A/150A/100A/70A MOS no Screen : 300A/200A/150A/100A/70A Current + MOS Tube , without others
300A/200A/150A/100A no MOS Screen : 300A/200A/150A/100A/70A Current ,without others
Only Display Screen: Only Display Screen, without others
Russia language video :http://www.youtube.com/watch?time_continue=1&v=9caa03JSWhM
BMS battery pack protection board function description:
Support :
7S -24S li-ion battery (24V-102V Lithium battery cell)
8S -24S lifePo4 battery (24V-88V Lithium iron phosphate battery cell)
10S -24S LTO battery (24V-68V Lithium titanate battery cell)
The default is the li-ion parameters. when you phone connect bluetooth , can click and set up lifePo4 / LTO parameters
Single cell voltage detection range 1V-4.6V. High precision detection cell voltage error is less than 5MA
Charging current 50A
Discharge current: 70A 100A 150A 200A 300A to choose
Balance current :200MA . Controlled equalization mode, when the charging is started, the pressure difference can be detected by the detected pressure difference to be greater than the set value.
High-precision coulomb counter function temperature control detection Hall speed measurement
1. Protection board support 8-24 cells any battery pack (lithium titanate, iron lithium, ternary, lifepo4
etc.) (greater than 18v)
2. Battery voltage detection, voltage detection range 1-5v (less than 1v and higher than 5v can not be detected), high precision, integrated error of less than 5mv, applicable to all the voltage within the scope of the battery pack used, overshoot Protection, over discharge protection voltage can be set within this range.
3. With a controlled equalization method, the charge can be balanced by detecting that the differential pressure is greater than the set value.
3. Current measurement (support within 300a current measurement)
4. High-precision coulometer function, based on the current on the time integral, accurate calculation of the remaining battery capacity, charge and so on.
5. Support Android phone set different battery parameters, see the single voltage and current information
6. Support the screen shows the battery status, parameters, each unit voltage
7. Based on the motor Hall pulse detection speed, and can calculate the remaining mileage
8. Independent 6-way temperature measurement, you can set the temperature over-temperature protection value
9. Dual independent watchdog real-time monitoring program plus two protection, never crash
?
10. Screen power supply 24V-100V 11.Protection board size: Length 15.5CM Width 7CM Thickness 2.5CM include these kits： 
8 - 24S Protection board description
- The protection board defaults to the ternary parameter mobile phone connection Bluetooth can choose to set the iron lithium parameter cargo titanium lithium parameters and the number of battery strings
- Single-cell voltage detection range 1-4.6V (less than 1V or higher than 4.6V can not be detected) High-precision detection monomer voltage error is less than 5MA overcharge protection, over-discharge protection, cell voltage can be arbitrarily set within this range
- Support ternary lithium 7-24S（24V- 102V Battery）
- Support lithium iron phosphate 8-24S （24V - 88V Battery )
- Support lithium titanate 10-24S （24V - 68V Battery）
- Discharge current: select greater than the maximum current amperage of the car remote control
- Equilibrium current: 200MA adopts controlled equalization mode. When charging, it can start to balance by detecting that the differential pressure is greater than the set value.
- Current measurement: support current measurement within 300
- High-precision coulomb counter function: based on current-to-time scoring, accurately calculate battery remaining capacity and charge capacity, etc.
- Parameter display: support Android mobile phone connection Bluetooth display parameter setting modify parameters, independent display display parameters
- Temperature control monitoring: protection board built-in balanced power 2 way temperature control monitoring can be external 4 channel battery temperature control monitoring
- Hall speed measurement: The display has a speed measurement function, based on the accurate detection speed of the motor Hall pulse, and can calculate the remaining mileage
- Never crash: set up independent watchdog real-time monitoring program plus secondary protection
- Support mobile phone Bluetooth connection
- Support a variety of cell use, modify parameters
- Intelligent and precise control of voltage, battery can live longer
- External temperature control monitoring battery, over temperature alarm protection
4 position temperature sensor wiring instructions:
Purchase 4 protection boards and 1 5P line plug
No external temperature sensor has no effect
- Cut the temperature sensor a little with scissors as shown in Figure 1.
- Figure 2 find two thin wires welded to the temperature sensor
- As shown in Figures 3 and 4, the four temperature sensors are welded to the heat shrinkable tube.
- As shown in Figure 5, the black line of the 5P line is connected to one line of four temperature sensors at the same time, and the other four red lines are connected to one temperature sensor.
- Note: The black line of the 5P line is the common line, and the other 4 lines are respectively T1 T2 T3 T4. The temperature of the 4 positions can be displayed on the mobile phone, and the temperature sensor is not divided into positive and negative poles.
As shown in Figure 6, the temperature sensor must be insulated again with high temperature tape.
Finally put 4 different positions of the battery and check the temperature of 4 positions of the battery.
Up to 4 external device
-
note:
It is strictly forbidden to separate the main board from the power board when the protection board is charged. Please disconnect B+ or B- before disconnecting the main board and the power board, and unplug the equalization line Otherwise it will burn the protection board
About the start and close buttons:
1. If the protection board is shut down due to abnormal power failure, just press the button to start the BMS.
2. During normal operation of the protection board, press and hold this button for more than 5 seconds, then release the button, the protection board will automatically turn off the power, stop working, zero power consumption, short press can realize the display of the matching protection board matching screen.
3. Protection board If the discharge tube is not turned on for more than 5 minutes, the protection board will automatically turn off the main power supply, stop working, and zero power consumption.
4. If the BMS power is turned off because of the 2nd and 3rd reasons, you need to press and hold the power button for 3 seconds to start the normal operation of the protection board.
5. If the matching display is connected, press this button shortly to switch the screen display.
6. Please ensure good insulation of the power button, otherwise the BMS power may not be automatically turned off.
About onboard Bluetooth：
1. After the BMS works normally, Bluetooth is activated and you can search and connect at this time:
Name: BMS_ANT Pairing password: 1234
Idea: After BMS is on standby, the Bluetooth power will be automatically turned off (if Bluetooth is connected, it will not be turned off), Bluetooth cannot be connected at this time (automatic standby defaults to no current for 3 minutes), can be discharged, or charged, BMS After the current is detected, the standby will be automatically released and Bluetooth will be turned back on. Before searching for Bluetooth signals, please make sure that the BMS is not on standby. If it is not found at one time, please try it multiple times.
Protection board calibration:
1. Monomer voltage calibration: It can be adjusted by “system reference voltage” (default 3.0 or so), and slowly increase and decrease by 0.001, and the monomer voltage value can be changed until accurate
2. Total pressure calibration: You can change the total pressure by adjusting the “total pressure calibration parameter” (default 3330 or so) to change the total pressure until it is accurate
3. Current calibration: You can change the current by adjusting the “current sensor range” and slowly change the current until it is accurate
Note: Please do not change the “Power Start Current” item in the parameter setting. If it is too large, it may cause the MOS tube to be burned and discharged
About the automatic equalization function:
The automatic equalization function is mainly a function set for the battery difference. The user must use the battery when it is fully charged or near full. When the battery is almost fully charged, unplug the charger and click " Automatic equalization", the protection board will automatically equalize until the battery pack pressure difference is less than 0.001, or the user clicks "automatic equalization" again to turn off, whether the automatic equalization is turned on or off can switch the screen to "system status" to view "equalization" "Status, if "Auto EQ" is displayed, it means that automatic equalization is in progress
Protection board wiring video:Https://v.qq.com/x/page/e05497w1x6t.html
Note: The protection board has many wirings and is sensitive and fragile. Every step of the wiring is carefully checked. It should not be sloppy. Every step must be insulated to prevent any short circuit (There are a lot of careless customers short-circuiting the board) The temperature sensor must also be insulated again and then loaded into the battery pack Otherwise, any consequences caused by the customer