JANPET Upgraded 1000m Remote Control Dog Hunting Beeper Collar 100% Waterproof beep Collars for Hunt dogs
![a8](https://ae01.alicdn.com/kf/HTB18xmudjfguuRjSszcq6zb7FXaf.jpg)
Discription:
The Upgraded Model is with remote controller. It can control 3 dogs at most with a range of 1000meters far away.
This model is built in inductor and equiped with magnetic switch. The Built-in buzzer, can produce 8 different "BIB" sounds, set this product on the dog&39;s neck, when the dog move fast the product will emit a short "BIB" sound,when the dog move slow or doesn&39;t move, means the dog has been found the prey, then the product will emit urgent and continuous "BIB" sounds.
Spec.
1: The unit size: L*W*H = 66 *70 *36 mm
2: 8 operating modes and 4 selecting tones for Pointing dog & Moving dog
3: LED power indication
4: Powered by 3V lithium CR123A battery
5: Water-proof design
6: Low power consumption
7: Locate one to four dogs at the same time
I. Remote control instruction:
1. Remote control can operate 3 beeps at the same time.
2. Remote control can operate PLAYand STOP function of the beeps.
3. The range between the beep and the remote control is more than 1000 meters.
4. Please use 23Abattery for the remote control, and 4.2V battery for the beep.
II. Coding function:
1. Use the magnetic switch to aim the switch position and the beep is on.
2. Press the coding key of the beep, red indicator will be on, then press any Akey of the remote control,
the red indicator of the beep will flash three times and then off, code is successfully matched, Akey can
operate PLAYand STOP of the current beep.
3. The same operation for the second beep, press any B key of the remote control, the red indicator of
the beep will be off after flashing three times, B key can operate PLAYand STOP of the second beep.
4. The same operation for the third beep, C key can operate PLAYand STOP of the third beep.
III. Remote control
Put the collar separately on the neck of 3 dogs, then pull out the antenna of the remote control, pressA、
B、C key to operate PLAYand STOP of 3 beeps
Package includes:
1x Traning Collar
1x Battery
1x Screwdriver
1x Multi-Language User Manual
1x Beeper Collar,
1x Magnetic switch
![UPDATED](https://ae01.alicdn.com/kf/HTB1q5VdKuSSBuNjy0Flq6zBpVXaF.jpg)
![1000xSAM_1427](https://ae01.alicdn.com/kf/HTB1bEbrd8cXBuNjt_Xoq6xIwFXaH.jpg)
![a2](https://ae01.alicdn.com/kf/HTB14QcGKkyWBuNjy0Fpq6yssXXaL.jpg)
![7](https://ae01.alicdn.com/kf/HTB1aF8VKrSYBuNjSspfq6AZCpXaC.jpg)
![10](https://ae01.alicdn.com/kf/HTB1LxH.vr3nBKNjSZFMq6yUSFXaA.jpg)
![12](https://ae01.alicdn.com/kf/HTB1bVnRB2iSBuNkSnhJq6zDcpXaI.jpg)
E:Setting the movement detection sensitivity
When leaving the factory,the collar is set to an intermediate position (medium sensitivity).It is up to you to adjust the sensitivity of your beeper to your dog&39;s behavior and to the results you want to obtain
To change the movement detection sensitivity,you need to remove the Plastic Casing of the collar in order to get access to the sensitivity adjustment screw located inside the collar
F:Adjusting sound volume
When leaving factory,the collar is set at the maximum volume,the system is set at the maximum stop.You can not turn beyond to increase sound volume
It is up to you to adjust your Beeper Collar sound volume to the level you wish
To adjust the volume of your collar,you need to lift the Plastic Casing in order to get access to the adjusting screw located inside the collar
To decrease the sound volume of your Beeper Collar,turn the volume adjustment screw clockwise to the minimum sound volume
To increase the sound volume of your Beeper Collar,turn the sound volume adjusting screw counter-clockwise to the maximum sound volume
Note:The adjustment system has a stop for the minimum sound volume and a stop for the maximum sound volume (maximum 1/2 turn)
![remote](https://ae01.alicdn.com/kf/HTB1TE7FKeOSBuNjy0Fdq6zDnVXax.jpg)