New 8 PCS CCD Sensor Cleaning Kit/Wet + Dry 2in1 CMOS Cleaner Dry SWAB for Camera DSLR Cameras +Free Shipping
Description:
CCD SWAB is specially designed for cleaning digital camera CCD/CMOS chips.
It is easy and safe to use, clean your digital camera sensor quickly and cost-effectively
Made of Plastic & Microfiber
Note:
1. It is suggested that one CCD SWAB only can be used ONCE in case secondary contamination.
2. Open one separated bag at one time to avoid contaminating spare swbs.
3. No any solution is requested.
First, how do you find that the CCD/CMOS sensor is dirty? Take a picture of the camera against the sky or white paper, and take a picture in a defocused state. Some black spots like the one below are not in the scene. That&x27;s the dust on your CCD/CMOS sensor, your camera is going to be clean
Second, how to clean? (1) Ultrasonic cleaning of the camera itself: If the camera itself has an ultrasonic cleaning function, it is cleaned with the cleaning function of the camera itself. If the dust black spots still exist after cleaning, proceed to the next cleaning. (B), the manual cleaning of the rising reflector: 1, how to raise the reflector? In recent years, the camera has a rising reflector cleaning sensor function in the menu. The camera that was produced in the early days, hit the shutter to the B door, use the lock function of the shutter release, open the shutter lock, and the reflector will not fall.
2, preparation: A, the environment: find a dust-free environment, generally can be operated in the bathroom, no dust between the guards. If the requirements are higher, first flush the air with a water jet at night, wet the floor, close the door of the bathroom, and let the dust fall slowly at night. The next morning, the dust in the air basically fell to the ground and was absorbed by the wetlands.
B. Tools: air blown or dust-free compressed air tank, cleaning stick or jelly pen, cleaning solution. To clean the CCD/CMOS sensor, use a special tool, a jelly pen or a jelly brush. If there are a lot of oily stubborn stains on the CCD/CMOS sensor, it is also necessary to cooperate with the CCD special cleaning agent. It is forbidden to use the ordinary lens cleaning solution, which will pollute the sensor&x27;s low-pass filter. Buy 10 bottles of cleaning solution. Or use 2:8 formula of anhydrous alcohol + ether (can be used in petroleum ether).
C. Power: Before cleaning, check if the camera battery is enough, because cleaning is to set up the lifting mirror in the camera. If there is no power, the mirror will fall and cause damage. First clean the outside of the camera with a blower. D. Operate the camera. After the mirror is raised, you can see the CCD/CMOS sensor. At this time, observe the surface of the sensor. The obvious dust is stained with a gas-blowing jelly pen, and then quickly follow the same one with a cleaning rod. Directional brush sensor surface, follow the rules of the first two sides. If the width of the cleaning rod is just right, then it is best. With a little bit of force, after cleaning, quickly lower the mirror. If it is a stubborn stain, it can be cleaned with a cleaning solution. It should be very traced. When it is applied, when brushing the CCD, a brush will evaporate without leaving traces. If the cleaning stick is brushed, it can&x27;t be cleaned, and you need to change another clean brush. It is best to brush only once.
Camera frame knowledge introduction: SLR camera CCD sensor area size, divided into full frame, APS-C frame, 4/3, micro single frame, etc. Full frame camera: Nikon: D600\D610\D700\D800\D3\D4, etc. Canon: 5D\5D2\D53\6D\1D, etc. Sony: A800\a850\a900 and other APS-C cameras: Canon: 7D, 600D, 550D, 500D, 450D, 40D, 50D, 60D, 70D, 1100D, 1000D, etc. Nikon :D100\D200\D300\D40\D50\D60\D70\D80\D90\D7000\D7100\D3000\D3100\D3200\D5000\D5100\D5200 and other Pentax: K10D\K20D\K30\K3\K5\K50\KX \KR\K100D\K200D and other Sony: a100\a200\a300\a450\a500\a550\a77\a55\NEX series and other micro-single: Olympus 4/3, M4/3, Samsung Micro, Nikon Micro A single CCD camera with a size smaller than 12 mm.
