Universal Treadmill Circuit board Treadmill Console display Treadmill motor control board controller1HP-2.0HP/1HP-4.0HPmotor
Package include:
1-2.0HP / 1-4.0HP controller *1
Display controller *1
safety key *1
cable *1
warranty:3 months
MAX speed: 12km/h
220V AC input(leave message for 110V or other), Apply for DC motor 90V-260V
This controller set can work 100% without a speed sensor, so no need to worry.
The controller of this kit with 3 pin, if your speed sensor magnetic with only 2 pin, connect 2 pin to 2 of 3pins of the controller is OK can use ↓
Please make sure:
a. Motor performance OK
b. Transmit function OK, especially belt, lubrication normal.
c. Only work for home treadmill use DC motor.
1-4.0HP with incline↓
1-4.0HP with no incline↓
1-2.0HP with incline↓
1-2.0HP with no incline↓
Real picture ↓
Controller type discrimination:
How to test:
1.Mode setting
Push M/P enter time countdown seting the time place will flashing and show the time data Push the ▲and ▼ change the time data. finish seting. push START/STOP the treadmill will enter Operating status after 3 seconds
Under the Time countdown seting, Push the M/P again, enter the distance countdown seting the distance place will flashing Push the ▲and ▼ change the distance data. finish seting. push START/STOP the treadmill will enter Operating status after 3 seconds
2.Calorie seting also the same .
3.Controller parameter settings
For example, we want to set the output torque of the controller;
Main steps:
3-1, unplug the "safety key", as shown below:
3-2: press ▲ and ▼ at the same time, after more than 3seconds, until the display appears "100"
And then release the button, enter the parameter setting mode as shown below:
3-3: Press the "Start / Stop" button,
"101" appears on the left side of the display window.
It indicates that the controller has entered the minimum speed setting at this time
As shown below
3-4: Continue pressing the "Start / Stop" button,
Until the display window on the left position appears "107"
Indicates that the "torque setting mode" as below
3-5: adjust the value by▲and ▼
After setting the value, press the "Start / Stop" button again,
"108" appears on the left side of the display window; it indicates confirmation,
The system will automatically save the settings;
3-6: The last step is to put the safety key up, it means that the end of the set;
Display code data meaning
"101" Minimum speed Unit KM/H range:0.5--3.0
"102" Maximum speed Unit KM/H range: 3.0--16
"103" Speed adjustment Unit KM/H range: 0.5--25
"104" Reserved
"105" Reserved
"106" Sensor mode switch
"107" Motor torque adjustment
"108" Overload current unit A 5.0--30.0
"109" Cut off current unit A 5.0--30.0
Please note:
103 is the motor speed calibration,
The greater the set value, the smaller the treadmill output speed;
If there is no sensor, the corresponding value of 103 corresponds to the greater the motor output.
106 is the sensor mode; 22.0 indicates the light sensor; 22.1 means no sensor
107 is the motor output torque, the greater the value of the motor output torque greater
When you have finished setting a parameter each time, be sure to press the "Start / Stop" button again to save the set parameters.
1: factors affecting the speed of the treadmill include the motor belt bearing, the ratio of the front roller, and different speed sensors, etc. they have a direct relationship
2: treadmill start smoothness with the treadmill motor characteristics of a relationship,
If the low speed, treadmill shock phenomenon, which means that the torque is too large.
3: If the treadmill in the high-speed when there will be noise, indicating that the motor with the control panel with a little problem, need to adjust.
4: If the treadmill at a certain speed noise, it is only the motor rotation up with the platform generated resonance point, with the motor quality and electronic control is not directly related.
5:5: We recommend customer to buy display+ controller whole set, otherwise it will cause can not start or burn the dashboard phenomenon
5.Please make sure that the motor is in working order before placing your order. How to identify whether the motor is in working order ↓
1.Use 2-3PCS 5 batteries
2.Connect like photo
3.See motor running or not
User feedback:
Feedback is the breakfast for the champion.Your feedback is very improtant to our business development and gauge of how can we doing. We sincerely invite you to leave positive feedback for us service.If you are satsdfied with our products and services.