433Mhz Universal Wireless Remote Control Switch AC 85V~250V 110V 220V 2CH Relay Receiver Module and 5pcs RF 433 Mhz Remote Controls
Technical Data:
Input Power:AC 85V-250V
Standby Current:<8.5MA
RF Frequency: 433M
RF working mode: superheterodyne
Receive sensitivity: > 97 dbm
Transmitting distance: More than 15 meters
Decoding mode: MCU software decoding
Learnable Transmitters: 1-16 transmitters
Support remote type: Learning code (1527)
Switching Modes:
Both Momentary & Toggle
Wiring type:fixed terminal
Switch Output : normally open & normally closed.
Dimension of PCB
(L,W,H)
35*30*18mm
1 3/8 * 1 3/16 * 11/16"
Switch Output:
NO: normal open
COM: common
NC: normal close
Wire port :
NO: normal open
COM: common
NC: normal close
HOW TO USE:
On this products details page, there is a demonstration video available.
You can also see the video at this URL:
https://youtu.be/k06q76qthBw
Working Modes explanation:
Momentary Mode:
Push the remote button , the relay activates, release the remote button the relay deactivates.
Toggle Mode:
Push and release the remote button , the relay activates.
Push and release the remote button again and the relay deactivates.
Clearing All Stored Transmitters:
**Note**
After clearing the stored transmitters, all transmitters will need to be relearned by the receiver.
Push the learning button on the receiver 8 times , and the codes will be cleared .
Learning the transmitter :(momentary Mode)
Programing a 2 button transmitter as momentary mode transmitter.
STEP 1
Push and release the learning key on the receiver ONCE.
Wait for a moment , the LED will turn off , indicating you entered the learning state.
STEP 2
Push and release the first button on your transmitter, the LED on the receiver board will flash on then off indicating the button was learned.
STEP 3
Press and release the second button, watching the LED go on and off again.
Wait 3 seconds, the LED will turn on again , indicating system is ready for use.
Learning the transmitter : ( Toggle Mode )
Programing a 2 button transmitter as toggle.
STEP 1
Press and release the learning key on the receiver TWICE.
Wait for a moment , the LED will turn off , indicating you entered the learning state.
STEP 2
Press and release the first button on your transmitter, the LED on the receiver board will flash on then turn off.
Indicating the button was learned.
STEP 3
Next press and release the second button, watching the LED go on and off again.
Wait 3 seconds, the LED indicator will turn on again , indicating system is ready for use
**Notice**
two button transmitters can only be used as toggle or momentary.
One mode per 2 button transmitter.
?(Please note: You let the control panel to learn the remote control, you must press the "A" and "B" button;
Rather than just pressing one of them )
However you can program another transmitter in the other mode.
Please note
255842611896530
Maybe You Need
433 Mhz Remote Control and 433Mhz Wireless Receiver Learning Code 1527 Decoding Module 4Ch output With Learning Button
/set
2pcs 433 Mhz Remote Control and 1pcs 433Mhz Wireless Receiver Learning Code 1527 Decoding Module 4Ch output With Learning Button
/set
433 Mhz Remote Control and 433Mhz Wireless Receiver Learning Code 1527 Decoding Module 4Ch output With Learning Button
/set
433mhz RF Receiver Learning Code Decoding Receiving Module 433 mhz Wireless 4 Channel output module With Learning Button diy kit
433 Mhz Wireless Receiver and Transmitter Remote Control Learning Code 1527 Decoding Module 4 Ch output With Learning Button
/set
3pcs 433Mhz Remote Control and 1pcs 433 Mhz Wireless Receiver Learning Code 1527 Decoding Module 4Ch output With Learning Button
/set
3pcs superheterodyne 433mhz rf Wireless receiver Module small size low power For remote control
1set RF module 433 Mhz superheterodyne receiver and transmitter Support ASK OOK small size low power kit For Arduino/ARM/MCU
/pair
433 mhz rf Wireless Receiver superheterodyne 433mhz UHF ASK remote control Module Kit small size low power For Remote Controls
433 Mhz Superheterodyne RF wireless transmitter module Built-in Encoding EV1527 Coding wide-voltage 3V-24V For remote control
1piece superheterodyne 433mhz RF Wireless Transmitter Module Small Size Low Power for remote control adruino diy kit